Overview
Introduction
This solution employs a router/server computer with two network interfaces, one is a network uplink, the other connects to the wifi routers with their respective supplicants.
Users authenticate using a username and password, and verify the identity of the RADIUS server using a certificate presented by the server (see more information under supplicant configuration).
As mentioned in '@@@', the NASes available do not support sending RADIUS accounting packets, they are only able to authenticate users against the response from a RADIUS server. This solution uses 802.1X to authenticate users and let them into the wireless network, and then Shorewall to perform the logging/accounting work. FreeRADIUS logs the MAC address of all devices that connect along with the username they authenticated as, this information can be used to match information in Shorewall's logs to a user session. For improved security the firewall policy will be to disallow all connections except those originating from known IP addresses of known wifi clients. A script, shwl_add.sh, gets run by FreeRADIUS upon successful authentication of a supplicant, which runs an ARP scan to find the IP address of the device with the MAC address specified by FreeRADIUS, it then adds the IP address to shorewall's "whitelist", logs the event along with some useful information to a MySQL database and writes the current timestamp to a text file. In Access-Accept packets the Session-Timeout and Termination-Action attributes are sent, informing the NAS that after the specified amount of time the supplicant needs to repeat the authentication process or be disconnected. When the supplicant repeats authentication the mentioned script detects that the supplicant is already known and simply logs the event to MySQL and updates the timestamp in the text file. Another script, shwl_del.sh, is run by crontab at a regular interval, which goes through all the IP addresses present in shorewall's "whitelist" and checks the timestamp of the corresponding supplicant's last authentication to FreeRADIUS in the corresponding text file. If more than the specified amount of time has passed, this script assumes that the supplicant has disconnected from the wifi network and removes its IP from shorewall's "whitelist", logs the event to MySQL, and deletes the related text files.
A python script, script_launcher.py, serves as an intermediary that is launched by FreeRADIUS using its Rlm_python module and in turn launches shwl_add.sh.
The database backend containing user credentials for FreeRADIUS is MySQL. Adding/deleting users can be accomplished by SQL queries which can be included in site specific custom user management scripts or as hooks to the standard 'adduser' and 'deluser' utilities (out of the scope of this guide). Updating of passwords is accomplished by a script, pam_to_mysql_update.sh, that gets run by the libpam-script PAM module during PAM stack execution, and updates the password in the MySQL database according to the same password the user chose for their system user account. An entry with the username field already filled and matching the system user account username needs to be already present in the MySQL database. Commands that expire or disable a user's system user account (or password) without deleting it (such as passwd -l) will not cause the credentials in the MySQL database to be disabled, thus it is necessary to take care (perhaps with a site specific lock user script) to also invalidate the same.
Shorewall dynamic zones are used to achieve the dynamic change of firewall rules set for the IP addresses added/removed to the "whitelist". The rules for the normal zone concerning the network connecting to the NASes/supplicants disallows all connections, except those needed for the RADIUS conversation between the NASes and FreeRADIUS. A dynamic zone is declared under the normal zone, whose rules allow network access, with logging. The 'shorewall add <dynamic_zone_name> <ip_address>' and 'shorewall delete <dynamic_zone_name> <ip_address>' commands can then be used by the shwl_*.sh scripts to change the rules applicable for the specified source IP address.
Sudo is installed and configured as it is required for some of the mentioned scripts to run commands as root or as a different user.
A package containing the mentiond scripts, as well as the empty MySQL schema for the database used by some of them, is attached to this wiki page.
Scripts
Common MySQL database schema
A MySQL schema is contained in the shwl_add_shwl_del_pmu.sql in the attached archive. It is used by the shwl_add.sh, shwl_del.sh and pam_to_mysql_update.sh scripts to log events and errors. It contains a single table named 'event_log', it's format is as follows:
...
shwl_add.sh
This script reads 10 lines on stdin, as follows:
...
RADIUS attribute: NAS-Port
...
The supplicant MAC address is used in the script, the remaining values are simply logged into the MySQL database. Some sanity check is performed on the username before the script continues. The supplicant MAC address is processed so as to obtain it in both of the following formats regardless of the format the NAS specified it in: filename friendly version: 0123456789ab, normal version: 01:23:45:67:89:ab. The script then checks if a file named as the filename friendly version of the supplicant MAC address already exists (referred to by the script as an IP file). If it does not, the script runs an ARP scan on the configured network interface and in the resulting table, looks for the IP address matching the specified supplicant MAC address. In case no such device is found, it repeats the scan a configurable amount of times at a configurable interval before giving up. Once a matching IP is found some amount of sanity check is performed on the scan results (e.g. to detect multiple MACs being used by the found IP), and then the event is logged into MySQL with "connect" mentioned in the 'event' column, the found IP is added to the configured shorewall dynamic zone, and a file named as the filename friendly version of the supplicant MAC address is created containing the device's IP, and a file named as the device's IP (referred to by the script as a timestamp file) is created containing the present timestamp. In case adding the IP address to the shorewall dynamic zone is not successful, the script waits a configurable amount of time, and then attempts a second time, after which it gives up (it was observed that it might happen that FreeRADIUS starts earlier in the boot process than Shorewall, and if this script is started during that timeframe the shorewall add command fails). In case the IP file is already present, the script simply logs the event to MySQL with "re-auth" mentioned in the 'event' column and re-writes the timestamp file with the present timestamp. In case an error is encountered, the script logs the error to MySQL mentioning "err-add-N" (where N is the error number) in the 'event' column, populating the remaining columns with their respective information as may be available at the time of the error, and exits immediately, returning the error number as exit code. In case access is available to the script's stdout and stderr, a description of the error message is also printed (and the script is quite verbose about what's happening), in case not, it is possible to look in the script's code for calls to the shwl_add_error_message_close() function, identify the call where the error number in question is passed to the function, and the error description can be found in the same function call. The configurable options can be found at the top of the script. The username is logged into the 'device_username' column, the IP address found during the scan is logged in the 'device_ip' column, the above mentioned normal version of the supplicant MAC address is logged in the 'device_mac' column, and the remaining RADIUS attributes are logged in the columns with the respective names.
This script is intended to be run by script_launcher.py (below mentioned).
shwl_del.sh '@@@'
This script loops through all the IP addresses present in the configured shorewall dynamic zone, reads their corresponding timestamp file (see shwl_add.sh description) and checks whether the configured amount of time has elapsed since. If it has, it logs the event to MySQL specifying "expire" in the 'event' column, removes the IP from the shorewall dynamic zone, deletes the timestamp file and searches for files (although there should be only one) containing the IP address (to find the IP file, see shwl_add.sh description) and deletes them. In the unexpected case that no timestamp file is found for a given IP or it does not contain a valid timestamp, the same actions are taken as when the configured amount of time has elapsed, but "untracked" is mentioned in the 'event' column instead of "expire". In case an error is encountered, the script logs the error to MySQL mentioning "err-del-N" (where N is the error number) in the 'event' column, populating the remaining columns with their respective information as may be available at the time of the error, but continues execution. At the end, it returns the error number as exit code, or, in case there were multiple errors, 127. In case access is available to the script's stdout and stderr, a description of the error message is also printed (and the script is quite verbose about what's happening), in case not, it is possible to look in the script's code for calls to the shwl_del_error_message() function, identify the call where the error number in question is passed to the function, and the error description can be found in the same function call. The configurable options can be found at the top of the script. No username is logged into the 'device_username' column, the IP address being processed is logged in the 'device_ip' column, a comma separated list of the IP files is logged in the 'device_mac' column, or the text "/// no-ip-files ///" in case no IP files were present, or the text "/// err-del-N ///" (where N is the error number) in case an error occurred while searching for the file(s), and the rad_attr_* columns are left empty. The text "/// n/a ///" may be present in the 'device_ip' and 'device_mac' columns if this information is not applicable.
This script is intended to be run by crontab at a regular interval.
script_launcher.py
pam_to_mysql_update.sh
Installation
Replication of production setup
Here, we replicate the relevant configuration already present on server.lastschl.av as a starting point. The test virtual machine will have two network interfaces, one serving as uplink on a 192.168.10.0/24 network (IP 192.168.10.52), and one to connect to the wifi routers/clients on a 192.168.9.0/24 network (IP 192.168.9.1). The FQDN will be server.test.av.
Base virtual machine preparation
Imported Last School's Debian9 VM template "Debian9-base.ova" into Virtual Box as Debian9-base_8021x, re-initializing all MAC addresses. The description for this virtual machine template is:
Code Block |
---|
Debian 9 amd64 installation
- Hostname:
debian9-base
- User accounts (username password):
ls last
root last
- Partitioning:
--- Physical:
------ 1GB RAID boot flag
------ 29GB RAID
--- RAID:
------ md0: ext3 /boot
------ md1: LVM - part of volume group debian9-base
--- LVM (VG/LV):
------ debian9-base/root: 18.6GB ext4 /
------ debian9-base/swap: 3.72GB swap area
- Up to date as of 2017-09-27
- sources.list includes:
Sections: main contrib non-free
Additional repository: backports
- Apt-cacher configured as per Last School site (Proxy credentials will need to be entered in /etc/apt/apt.conf.d/02proxy by user)
- SSH access installed and enabled
- Gnome and Firefox configured to auto-detect proxy settings
- Extra software installed:
vlc gimp emacs fonts-indic tcpdump iperf exfat-utils wireshark
- One network interface as bridged adapter, cable connected. |
...
The host computer has two network interfaces, one connected to a network uplink and another connected to a couple of wifi routers. Each VirtualBox virtual interface is bridged to a different physical adapter. Network configuration is now as follows (interface name seen in guest OS - Adapter name in VirtualBox settings - Adapter "Attached to" setting in VirtualBox settings - Physical interface bridged to):
enp0s3 - Adapter 1 - Bridged adapter- physical interface connected to uplink
enp0s8 - Adapter 2 - Bridged adapter - physical interface connected to wifi routers
Booted the VM, logged in to the GUI, connected using DHCP with network manager
In terminal:
Code Block |
---|
rm /etc/apt/apt.conf.d/02proxy
apt-get update
apt-get upgrade |
Rebooted the virtual machine
Set strong passwords for ls and root users
Installed my ssh public key in root's .ssh/authorized_keys file.
Installation of relevant services:
Shorewall (based on LASTSCHL-207):
Code Block |
---|
apt-get install shorewall
apt-get install ipset
mv /etc/shorewall{,-orig}
mkdir /etc/shorewall
|
Configuration:
Code Block |
---|
root@debian9-base:/etc/shorewall# for i in `ls`; do echo "========= $i ========="; cat $i | grep -v "^#" | grep -v "^$"; echo "========= $i ========="; echo ""; done
========= hosts =========
========= hosts =========
========= interfaces =========
net enp0s3 detect tcpflags,dhcp,nosmurfs,routefilter,logmartians
wifi enp0s8 detect tcpflags,nosmurfs,routefilter,logmartians
========= interfaces =========
========= masq =========
enp0s3 192.168.9.0/24
========= masq =========
========= policy =========
$FW net REJECT INFO(uid)
$FW wifi ACCEPT INFO(uid)
wifi all REJECT
net all DROP INFO
all all REJECT info
========= policy =========
========= routestopped =========
========= routestopped =========
========= rules =========
Invalid(DROP) net all
ACCEPT:INFO(uid) net $FW tcp 22
ACCEPT:INFO(uid) net $FW udp 123
ACCEPT:INFO(uid) net $FW icmp
ACCEPT:INFO(uid) $FW net tcp 465,587,995,993
ACCEPT:INFO(uid) $FW net udp 53,123
ACCEPT:INFO(uid) $FW net icmp
ACCEPT:INFO(uid) $FW net tcp - - - - root
ACCEPT:INFO(uid) $FW net udp - - - - root
ACCEPT:INFO(uid) $FW net icmp - - - - root
ACCEPT:INFO(uid) $FW net tcp - - - - _apt
ACCEPT:INFO(uid) $FW net udp - - - - _apt
ACCEPT:INFO(uid) $FW net icmp - - - - _apt
========= rules =========
========= shorewall.conf =========
....
STARTUP_ENABLED=Yes
....
IP_FORWARDING=On
....
========= shorewall.conf =========
========= zones =========
fw firewall
net ipv4
wifi ipv4
========= zones =========
|
In /etc/default/shorewall, set
Code Block |
---|
startup=1 |
Code Block |
---|
root@debian9-base:~# cat /etc/rsyslog.d/40-shorewall.conf
:msg, contains, "Shorewall:" /var/log/shorewall
& stop
root@debian9-base:~# cat /etc/logrotate.d/shorewall
/var/log/shorewall-init.log {
weekly
rotate 108
compress
nomissingok
create 0640 root adm
}
/var/log/shorewall
{
rotate 731
daily
nomissingok
notifempty
delaycompress
compress
dateext
postrotate
reload rsyslog >/dev/null 2>&1 || true
endscript
}
root@debian9-base:~# cat /etc/logrotate.d/rsyslog
/var/log/syslog
/var/log/auth.log
{
rotate 731
daily
dateext
nomissingok
notifempty
delaycompress
compress
postrotate
invoke-rc.d rsyslog rotate > /dev/null
endscript
}
/var/log/mail.info
/var/log/mail.warn
/var/log/mail.err
/var/log/mail.log
/var/log/daemon.log
/var/log/kern.log
/var/log/user.log
/var/log/lpr.log
/var/log/cron.log
/var/log/debug
/var/log/messages
{
rotate 4
weekly
missingok
notifempty
compress
delaycompress
sharedscripts
postrotate
invoke-rc.d rsyslog rotate > /dev/null
endscript
}
root@debian9-base:~# cat /etc/logrotate.conf
# see "man logrotate" for details
# rotate log files weekly
weekly
# keep 4 weeks worth of backlogs
rotate 4
# create new (empty) log files after rotating old ones
create
# uncomment this if you want your log files compressed
#compress
# packages drop log rotation information into this directory
include /etc/logrotate.d
# no packages own wtmp, or btmp -- we'll rotate them here
/var/log/wtmp {
nomissingok
monthly
create 0664 root utmp
rotate 24
}
/var/log/btmp {
nomissingok
monthly
create 0660 root utmp
rotate 24
}
# system-specific logs may be configured here
|
Code Block |
---|
systemctl enable shorewall.service |
Configure network and DHCP (based on LASTSCHL-212):
Code Block |
---|
systemctl disable network-manager.service
systemctl disable NetworkManager.service
unlink /etc/resolv.conf
echo nameserver 192.168.10.1 > /etc/resolv.conf
mkdir /etc/ltsp
|
Code Block |
---|
root@debian9-base:~# cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The external interface
auto enp0s3
iface enp0s3 inet static
address 192.168.10.52
network 192.168.10.0
netmask 255.255.255.0
broadcast 192.168.10.255
gateway 192.168.10.1
# The wifi interface
auto enp0s8
iface enp0s8 inet static
address 192.168.9.1
netmask 255.255.255.0
broadcast 192.168.9.255
root@debian9-base:~# cat /etc/dhcp/dhcpd.conf | grep -v "^#" | grep -v "^$"
# Some of the following lines are there by default and are probably not required
ddns-update-style none;
option domain-name "example.org";
option domain-name-servers ns1.example.org, ns2.example.org;
default-lease-time 600;
max-lease-time 7200;
log-facility local7;
include "/etc/ltsp/dhcpd.conf";
root@debian9-base:~# cat /etc/ltsp/dhcpd.conf
#
# Default LTSP dhcpd.conf config file.
#
authoritative;
subnet 192.168.9.0 netmask 255.255.255.0 {
range 192.168.9.40 192.168.9.250;
option domain-name "test.av";
option domain-name-servers 192.168.9.1;
option broadcast-address 192.168.9.255;
option routers 192.168.9.1;
option subnet-mask 255.255.255.0;
option root-path "/opt/ltsp/amd64";
if substring( option vendor-class-identifier, 0, 9 ) = "PXEClient" {
filename "/ltsp/amd64/pxelinux.0";
} else {
filename "/ltsp/amd64/nbi.img";
}
} |
Code Block |
---|
apt-get install isc-dhcp-server |
In /etc/default/isc-dhcp-server, set:
Code Block |
---|
INTERFACESv4="enp0s8" |
Configure DNS (based on LASTSCHL-211):
Code Block |
---|
apt-get install dnsmasq
touch /var/log/dnsmasq
chmod 640 /var/log/dnsmasq |
Code Block |
---|
root@debian9-base:~# cat /etc/dnsmasq.conf | grep -v "^#" | grep -v "^$"
strict-order
interface=enp0s8
expand-hosts
domain=test.av
log-queries
log-facility=/var/log/dnsmasq
root@debian9-base:~# cat /etc/logrotate.d/dnsmasq
/var/log/dnsmasq
{
rotate 731
daily
nomissingok
notifempty
delaycompress
compress
dateext
postrotate
reload rsyslog >/dev/null 2>&1 || true
endscript
}
root@debian9-base:~# cat /etc/hostname
server.test.av
root@debian9-base:~# cat /etc/hosts
127.0.0.1 localhost
192.168.9.1 test.av
192.168.9.1 server.test.av server
# The following lines are desirable for IPv6 capable hosts
::1 localhost ip6-localhost ip6-loopback
ff02::1 ip6-allnodes
ff02::2 ip6-allrouters |
New stuff
Now that we have a working setup similar to the production one, we will modify it to implement the new solution.
Download the latest version of the attached shwl_add_shwl_del_sl_pmu archive and extract it somewhere convenient.
Shorewall
Add to /etc/shorewall/hosts:
Code Block |
---|
wifi1 enp0s8:dynamic |
...
Code Block |
---|
# Just after: wifi all REJECT
# Added:
wifi1 net ACCEPT INFO
wifi1 $FW ACCEPT INFO(uid)
$FW wifi1 ACCEPT INFO(uid)
# Before: net all DROP INFO |
...
Code Block |
---|
....
wifi1:wifi ipv4 dynamic_shared |
In /etc/shorewall/shorewall.conf set:
Code Block |
---|
SAVE_IPSETS=Yes |
Add to /etc/shorewall/rules (replace IP addresses with actual IP address of wifi routers):
Code Block |
---|
# At the top of the file:
?SECTION ALL
# Allow the server and NASes to talk RADIUS and HTTP (web interface)
ACCEPT wifi:192.168.9.2,192.168.9.3,192.168.9.4 $FW tcp - 80
ACCEPT $FW wifi:192.168.9.2,192.168.9.3,192.168.9.4 tcp 80 -
ACCEPT wifi:192.168.9.2,192.168.9.3,192.168.9.4 $FW udp 1812 -
ACCEPT $FW wifi:192.168.9.2,192.168.9.3,192.168.9.4 udp - 1812
# But, reject anything else to and from any other device part of the 192.168.9.0/24 network that is not part of any dynamic zone
REJECT wifi all - - -
REJECT all wifi - - -
?SECTION NEW
# At the end of the file:
ACCEPT:INFO(uid) wifi:192.168.9.2,192.168.9.3,192.168.9.4 $FW udp 1812 |
FreeRADIUS
Code Block |
---|
apt-get install freeradius
systemctl enable freeradius.service |
Modify /etc/freeradius/3.0/mods-available/eap:
comment the following:
Code Block |
---|
....
# md5 {
# }
....
# leap {
# }
....
# gtc {
# # The default challenge, which many clients
# # ignore..
# #challenge = "Password: "
#
# # The plain-text response which comes back
# # is put into a User-Password attribute,
# # and passed to another module for
# # authentication. This allows the EAP-GTC
# # response to be checked against plain-text,
# # or crypt'd passwords.
# #
# # If you say "Local" instead of "PAP", then
# # the module will look for a User-Password
# # configured for the request, and do the
# # authentication itself.
# #
# auth_type = PAP
# }
....
# tls {
# # Point to the common TLS configuration
# tls = tls-common
#
# #
# # As part of checking a client certificate, the EAP-TLS
# # sets some attributes such as TLS-Client-Cert-CN. This
# # virtual server has access to these attributes, and can
# # be used to accept or reject the request.
# #
# # virtual_server = check-eap-tls
# }
.... |
modify the 'default_eap_type' directive under section 'eap' to be:
Code Block |
---|
default_eap_type = peap |
and the 'default_eap_type' directive under section 'ttls' to be:
Code Block |
---|
default_eap_type = mschapv2 |
Modify /etc/freeradius/3.0/sites-available/default, comment the following lines (see comments included in the code block):
Code Block |
---|
# All the listen sections except the IPv4 version with "type = auth"
listen {
ipaddr = *
port = 0
type = acct
limit {
}
}
listen {
type = auth
ipv6addr = :: # any. ::1 == localhost
port = 0
limit {
max_connections = 16
lifetime = 0
idle_timeout = 30
}
}
listen {
ipv6addr = ::
port = 0
type = acct
limit {
}
}
# In the authorize section:
chap
mschap
digest
files
-ldap
pap
# In the authenticate section:
Auth-Type PAP {
pap
}
Auth-Type CHAP {
chap
}
Auth-Type MS-CHAP {
mschap
}
mschap
digest |
Uncomment the following line in the 'authorize' section:
Code Block |
---|
auth_log |
Add the following line at the end of the 'post-auth' section and at the beginning of the Post-Auth-Type REJECT section:
Code Block |
---|
reply_log |
Add the following in the post-auth section, just before the Post-Auth-Type REJECT section:
Code Block |
---|
update reply {
Session-Timeout := 3600
Termination-Action := 1
} |
Modify /etc/freeradius/3.0/sites-available/inner-tunnel, comment the following lines:
Code Block |
---|
# The whole listen section
listen {
ipaddr = 127.0.0.1
port = 18120
type = auth
}
# In the authorize section:
chap
mschap
files
-ldap
# In the authenticate section:
Auth-Type PAP {
pap
}
Auth-Type CHAP {
chap
}
Auth-Type MS-CHAP {
mschap
} |
Add the following line after 'filter_username' and before 'suffix' in the 'authorize' section:
Code Block |
---|
auth_log |
Add the following line at the end of the 'post-auth' section and at the beginning of the Post-Auth-Type REJECT section:
Code Block |
---|
reply_log |
Modify /etc/freeradius/3.0/radiusd.conf, set (in the 'log' section):
Code Block |
---|
auth = yes |
Modify /etc/freeradius/3.0/clients.conf, comment the 'client localhost' and 'client localhost_ipv6' section and add (replace with actual IP addresses of wifi routers):
Code Block |
---|
client wifi-ap1 {
ipaddr = 192.168.9.2
secret = password # Replace with an actual password
}
client wifi-ap2 {
ipaddr = 192.168.9.3
secret = password # Replace with an actual password
}
client wifi-ap3 {
ipaddr = 192.168.9.4
secret = password # Replace with an actual password
} |
Modify /etc/logrotate.d/freeradius, modify the following options as follows ('dateext' option needs to be added):
Code Block |
---|
rotate 732
nomissingok
dateext |
Code Block |
---|
rm /var/log/freeradius/radius.log
rm /var/log/freeradius/radwtmp
chmod o-rwx /var/log/freeradius
chown freerad:freerad /var/log/freeradius
chmod o-rwx /etc/freeradius |
It has been observed that radius.log comes with world-readable permissions upon installation of the package, deleting it causes FreeRADIUS to re-create it, and it gets re-created with more secure permissions. /etc/freeradius also comes with the executable bit set for all users, which makes it easier for sensitive information contained within to be world-readable in case the permissions of an individual file are not set restrictive enough (as was, by default, the case with the file containing the encryption passwords for the SSL certificates). Could not find any information on the net on whether there is a good reason for the executable bit being set, so, decided it is safer to remove it.
...
Modify /etc/freeradius/3.0/certs/server.cnf, set the following settings:
Code Block |
---|
...
[ CA_default ]
...
default_days = 732
...
[ req ]
...
input_password = password # Replace with an actual password
output_password = password # Replace with an actual password, should be same as input_password
...
[certificate_authority]
countryName = IN
stateOrProvinceName = Tamil Nadu
localityName = Auroville
organizationName = Test
emailAddress = admin@test.av
commonName = "Test Certificate Authority"
... |
Modify /etc/freeradius/3.0/certs/ca.cnf, set the following settings:
Code Block |
---|
...
[ CA_default ]
...
default_days = 732
...
crlDistributionPoints = URI:http://server.test.av/test_ca.crl
[ req ]
...
input_password = password # Replace with an actual password
output_password = password # Replace with an actual password, should be same as input_password
[server]
countryName = IN
stateOrProvinceName = Tamil Nadu
localityName = Auroville
organizationName = Test
emailAddress = admin@test.av
commonName = "Test Server Certificate"
[v3_ca]
...
crlDistributionPoints = URI:http://server.test.av/test_ca.crl
... |
Code Block |
---|
cd /etc/freeradius/3.0/certs
rm -f *.pem *.der *.csr *.crt *.key *.p12 serial* index.txt* # This step is probably not needed,
make ca.pem
make ca.der
make server.pem
make server.csr
chown freerad:freerad *
chmod o-rwx *
rm bootstrap
rm passwords.mk
# Delete all other files in the folder except: server.cnf, ca.cnf, xpextensions, Makefile, README, dh, ca.pem, server.pem, server.key |
Modify /etc/freeradius/3.0/mods-available/eap, modify the following directives under section 'tls-config tls-common' to be:
Code Block |
---|
private_key_password = password # Replace password with the password chosen previously '@@@' same or different?
private_key_file = /etc/freeradius/3.0/certs/server.pem
....
certificate_file = /etc/freeradius/3.0/certs/server.pem
....
ca_file = /etc/freeradius/3.0/certs/ca.pem |
MySQL
Code Block |
---|
apt-get install mysql-server freeradius-mysql
mysql -uroot
CREATE DATABASE radius;
exit
mysql -uroot radius < /etc/freeradius/3.0/mods-config/sql/main/mysql/schema.sql |
Edit /etc/freeradius/3.0/mods-config/sql/main/mysql/setup.sql. Modify the following lines:
Code Block |
---|
CREATE USER 'radius'@'localhost';
SET PASSWORD FOR 'radius'@'localhost' = PASSWORD('radpass'); |
to
Code Block |
---|
CREATE USER 'freerad'@'localhost' IDENTIFIED VIA unix_socket; |
and update the username 'radius' to be 'freerad' wherever else it is mentioned in the file.
Code Block |
---|
mysql -uroot radius < /etc/freeradius/3.0/mods-config/sql/main/mysql/setup.sql |
Code Block |
---|
cd /etc/freeradius/3.0/mods-enabled
ln -s ../mods-available/sql sql |
In /etc/freeradius/3.0/mods-enabled/sql, set the following options:
Code Block |
---|
driver = "rlm_sql_mysql"
dialect = "mysql"
server = "localhost"
port = 3306
login = "freerad"
password = ""
radius_db = "radius"
logfile = ${logdir}/sqllog.sql |
Modify /etc/freeradius/3.0/sites-enabled/inner-tunnel, find the following line under authorize, post-auth and Post-Auth-Type REJECT sections
Code Block |
---|
-sql |
modify it to
Code Block |
---|
sql |
Modify /etc/freeradius/3.0/sites-enabled/default, find the following line under authorize, post-auth and Post-Auth-Type REJECT sections
Code Block |
---|
-sql |
In the post-auth and Post-Auth-Type REJECT sections, modify it to
Code Block |
---|
sql |
In the authorize section, comment it out.
Python module / script_launcher.py script
Code Block |
---|
apt-get install libpython2.7-dev # It is not fully sure whether this package is needed
cd /etc/freeradius/3.0/mods-enabled
ln -s ../mods-available/python python |
Put the following in it:
Code Block | ||
---|---|---|
| ||
#
# Make sure the PYTHONPATH environmental variable contains the
# directory(s) for the modules listed below.
#
# Uncomment any func_* which are included in your module. If
# rlm_python is called for a section which does not have
# a function defined, it will return NOOP.
#
python {
module = script_launcher
python_path = ${modconfdir}/${.:name}:/usr/lib/python2.7
mod_post_auth = ${.module}
func_post_auth = post_auth
}
|
Modify /etc/freeradius/3.0/sites-enabled/inner-tunnel:
Code Block | ||
---|---|---|
| ||
...
# Add this line just after 'sql' in the 'post-auth' section
python
... |
Modify /etc/freeradius/3.0/mods-available/eap, modify the 'copy_request_to_tunnel' directive under both sections 'peap' and 'ttls' to be:
Code Block |
---|
copy_request_to_tunnel = yes |
Place the script_launcher.py script from the shwl_add_shwl_del_sl_pmu archive at /etc/freeradius/3.0/mods-config/python/script_launcher.py
Code Block |
---|
chown freerad:freerad /etc/freeradius/3.0/mods-config/python/script_launcher.py
chmod 640 /etc/freeradius/3.0/mods-config/python/script_launcher.py |
sudo
Code Block |
---|
apt-get install sudo |
Create /etc/sudoers.d/shwl_add_shwl_del_pmu, permissions 640 root:root, with:
Code Block |
---|
freerad ALL=(root:root) NOPASSWD:/sbin/shorewall,/usr/bin/arp-scan |
shwl_add / shwl_del scripts
Prerequisites from above steps: sudo, FreeRADIUS python module / script_launcher.py script, shorewall, FreeRADIUS MySQL
Code Block |
---|
apt-get install arp-scan
# Install the shwl_*.sh scripts from the shwl_add_shwl_del_sl_pmu archive in /usr/local/sbin/
chown root:freerad /usr/local/sbin/shwl_*
chmod 750 /usr/local/sbin/shwl_*
mkdir /var/local/shwl_add
chown freerad:freerad /var/local/shwl_add
chmod 700 /var/local/shwl_add
chmod a-s /var/local/shwl_add |
Add the following line to freerad's crontab
Code Block |
---|
*/1 * * * * /usr/local/sbin/shwl_del.sh |
Settings in /usr/local/sbin/shwl_add.sh (at top of file):
Code Block |
---|
....
# Settings
cfg_shwl_zone="wifi1" # Shorewall dynamic zone to which client devices' IP addresses need to be added
cfg_shwl_retry_delay=2 # Number of seconds to wait, in case of failure in adding IP to shorewall dynamic zone, before attempting second time
cfg_file_location="/var/local/shwl_add" # Folder where runtime information will be stored
cfg_file_location_owner_user="freerad" # User by which above folder should be owned
cfg_file_location_owner_group="freerad" # Group by which above folder should be owned
cfg_ip_srch_iface="enp0s8" # Network interface on which to scan for devices
cfg_ip_srch_initial_delay=1 # How many seconds to wait before first attempt at scanning
cfg_ip_srch_retry_delay=2 # How many seconds to wait in between further attempts at scanning
cfg_ip_srch_max_attempts=15 # Maximum number of attempts at scanning before giving up
cfg_mysql_user="freerad" # MySQL username
cfg_mysql_db="shwl_add_shwl_del_pmu" # MySQL database name where to log events
cfg_mysql_log_table="event_log" # Table in MySQL database where to log events
.... |
Settings in /usr/local/sbin/shwl_del.sh (at top of file):
Code Block |
---|
....
# Settings
cfg_ip_match_pattern="192.168." # Pattern to match all IP addresses that might be in the shorewall dynamic zone
cfg_session_expiry_timeout=3660 # Session duration (should be slightly longer than Session-Timeout attribute specified in FreeRADIUS)
cfg_shwl_zone="wifi1" # Shorewall dynamic zone containing clients' IP addresses
cfg_file_location="/var/local/shwl_add" # Folder where runtime information is stored
cfg_file_location_owner_user="freerad" # User by which above folder should be owned
cfg_file_location_owner_group="freerad" # Group by which above folder should be owned
cfg_mysql_user="freerad" # MySQL username
cfg_mysql_db="shwl_add_shwl_del_pmu" # MySQL database name where to log events
cfg_mysql_log_table="event_log" # Table in MySQL database where to log events
.... |
MySQL
Code Block |
---|
mysql -uroot
CREATE DATABASE shwl_add_shwl_del_pmu;
GRANT ALL on shwl_add_shwl_del_pmu.event_log TO 'freerad'@'localhost';
exit
mysql -uroot shwl_add_shwl_del_pmu < shwl_add_shwl_del_pmu.sql # Updating shwl_add_shwl_del_pmu.sql to the full path of the shwl_add_shwl_del_pmu.sql file extracted from the shwl_add_shwl_del_sl_pmu archive |
pam_to_mysql_update.sh script
Prerequisities from above: sudo, FreeRADIUS MySQL, shwl_add / shwl_del scripts MySQL
Code Block |
---|
apt-get install libpam-script sshpass
mkdir /usr/share/libpam-script/pam-script.d/pam_to_mysql_update
cd /usr/share/libpam-script/pam-script.d/pam_to_mysql_update
# Install the pam_to_mysql_update.sh script from the shwl_add_shwl_del_sl_pmu archive in here
ln -s pam_to_mysql_update.sh pam_script_auth
ln -s pam_to_mysql_update.sh pam_script_passwd
mysql -uroot
GRANT ALL on radius.radcheck TO 'freerad'@'localhost';
exit
pam-auth-update # And, uncheck the box for "Support for authentication by external scripts" |
Add the following line at the end of /etc/pam.d/common-auth:
Code Block | ||
---|---|---|
| ||
....
auth required pam_script.so onerr=fail dir=/usr/share/libpam-script/pam-script.d/pam_to_mysql_update/ |
Add the following line at the end of /etc/pam.d/common-password:
Code Block | ||
---|---|---|
| ||
....
password required pam_script.so onerr=fail dir=/usr/share/libpam-script/pam-script.d/pam_to_mysql_update/ |
Settings in /usr/share/libpam-script/pam-script.d/pam_to_mysql_update/pam_to_mysql_update.sh (at top of file):
Code Block |
---|
....
# Settings
cfg_mysql_user="freerad" # MySQL username
cfg_mysql_user_db="radius" # MySQL database name where to update passwords
cfg_mysql_log_db="shwl_add_shwl_del_pmu" # MySQL database name where to log events
cfg_mysql_user_table="radcheck" # Table in MySQL database where to update passwords
cfg_mysql_log_table="event_log" # Table in MySQL database where to log events
cfg_verbose=0 # Print verbose messages on stdout
.... |
Managing users
The below procedures also create/change password for/delete system users as well as users for FreeRADIUS.
Adding users
Replace 'user' with the desired username.
Code Block |
---|
mysql -uroot
use radius;
INSERT INTO radcheck VALUES ('','user','NT-Password',':=','');
exit
adduser user # When prompted for "Current password:", ignore and press enter |
Changing password
It is sufficient to use standard utilities such as 'passwd', the password will be updated in the MySQL database as well. Tested with 'passwd' and User Accounts applet in GNOME. In case prompted with "Current password:" (exactly as written here) it is sufficient to ignore and press enter. Commands that expire or disable a user's system user account (or password) without deleting it (such as passwd -l) will not cause the credentials in the MySQL database to be disabled, thus it is necessary to take care (perhaps with a site specific lock user script) to also invalidate the same.
Deleting users
Replace 'user' with the username to be deleted.
Code Block |
---|
mysql -uroot
use radius;
DELETE FROM radcheck WHERE username='user';
exit
deluser user |
WiFi router (NAS) configuration
Settings to be configured
These are the settings that usually need to be configured, on dual-band routers it might be necessary to configure some of the settings twice, once under the settings for the 2.4GHz SSID and once for the 5GHz SSID:
- SSID - SSID of choice
- Network security type: WPA2 Enterprise
- WPA type: Set to either Auto or WPA2
- WPA encryption: Set to either Auto or AES
- RADIUS server IP - 192.168.9.1
- RADIUS server port - 1812
- RADIUS server secret/password - Password chosen in clients.conf for this particular NAS
- Clients isolation '@@@'
- IP address - IP address needs to match IP mentioned in clients.conf
- Disable DHCP
- Some models: Reauthentication period - Specify to something equal to or greater than the Session-Timeout specified in /etc/freeradius/3.0/sites-available/default. Some NASes interpret 0 as disabling re-authentication, and might then also ignore any value mentioned by the FreeRADIUS Session-Timeout / Termination-Action attributes.
- Some models: WPA2/RSN preauthentication '@@@' '@@@' order
- Secure password - Choose a secure password for accessing the NAS web (or other) interface. It is important as it controls access to the wireless security settings, and the web (or other) interface is reachable by supplicants connected to the network.
- Some models: Operation mode - Some NASes have an Operation mode setting, which sets/locks some settings to defaults that are appropriate for different kinds of uses, e.g. "DSL Router", "Wireless Router", "Wireless Access Point". This varies by model, but usually something like "Wireless Access Point" is a good first choice, if available, alternatively "Wireless Router"
TP-Link Archer C20 v4 00000004
In this model, the "Reauthentication period" setting is not available, but the router does honor the timeout specified by the RADIUS server. Operation mode can be set to "Access Point". All other settings should be set as mentioned above. This is a dual band router and some settings need to be set in two places, once for each SSID.
TP-Link TD-W8968 V4 0x00000001
In this model, the "Reauthentication period" setting is available as "Network Re-auth Interval", and the router also does honor the timeout specified by the RADIUS server, and follows whichever is smaller. Setting the setting to zero causes the feature to be disabled and the timeout specified by the RADIUS server to also be ignored. Operation mode can be set to "Wireless Router Mode". All other settings should be set as mentioned above.
TP-Link TL-WR740N v4 00000000
In this model, the "Reauthentication period" setting is not available, and the router does not honor the timeout specified by the RADIUS server. The hostapd daemon running on this router supports the feature and works in a similar way as in the above TP-Link TD-W8968 V4, but no option to configure it is available in the web interface, and hostapd is run with this setting set to 0. Judging by the source code of this (very old) version of hostapd, it is believed (but not tested) that this means, once authenticated, the router might allow the supplicant to continue being part of the network for up to twelve hours without querying the RADIUS server again. No operation mode setting is available. All other settings should be set as mentioned above. '@@@'
Supplicant configuration
Linux
- Copy the .ca file generated during certificate generation onto the computer.
- Select the network's SSID from the list in Network Manager.
- When asked, enter the following information, then press connect:
CA certificate: Browse and select the .ca file
Identity: the username
Password: the password
Leave all other fields as they are
Android
- Copy the .ca file generated during certificate generation onto the phone.
- Open the “Settings” app, go to “Wi-Fi” → “Advanced settings” → “Install certificates”.
- Select the .ca file.
- Assign it a name of choice
- Under “Certificate use” select “WiFi”
- Once again, open the “Settings” app, go to “Wi-Fi”, and select the network's SSID from the list.
- When asked, enter the following information, then press connect:
CA certificate: Select the earlier chosen name when installing the .ca file
Identity: the username
Password: the password
Leave all other fields as they are
Windows 10
- Select the network's SSID from the list of wireless networks
- Enter username and password
- When prompted whether to trust the server, confirm
Mac OS
- Select the network's SSID from the list of wireless networks
- Enter username and password
- When prompted whether to trust the server, confirm
iPhone
- Select the network's SSID from the list of wireless networks
- Enter username and password
- When prompted whether to trust the server, confirm
Security observations
On Linux and Android supplicants it is required to install the .ca file generated during certificate generation in order to verify the RADIUS server's identity. In case the identity presented by the RADIUS server changes at any point, the supplicant fails to connect, and re-presents the user with the prompt for network credentials. It is possible to connect without installing the .ca file, but one needs to specify "No CA certificate required" or "Do not validate". In this case the supplicant will send credentials to any RADIUS server for that SSID without verifying its identity. It is possible to avoid sending the real user name in the unencrypted outer tunnel, by specifying a different value (normally 'anonymous') in the "Anonymous identity" field.
On Mac OS and iPhone supplicants, when connecting to the SSID for the first time, the server certificate's details are presented to the user and the user is asked if they want to trust the server. In case the identity presented by the RADIUS server changes at any point, the user will be prompted with a message, not containing any warning, sadly, that looks identical to the one displayed when connecting for the first time, where a user is extremely likely to press Trust once again. On Mac OS, it is also possible to copy the .ca file and install it, avoiding the prompt on first connect, on iPhone, on the iPhone this was tested on, this did not have any effect. It seems to be possible, but greatly complicated (involving installing a software from the App Store, and using it to create a configuration profile which then needs to be saved to a file, copied and imported onto the supplicant device) to configure the supplicant to not send the real user name in the unencrypted outer tunnel.
Windows 10 '@@@'
Sources
https://wiki.freeradius.org/guide/Basic-configuration-HOWTO
https://wiki.freeradius.org/guide/SQL-HOWTO-for-freeradius-3.x-on-Debian-Ubuntu
https://wiki.freeradius.org/modules/Rlm_python
https://wiki.freeradius.org/config/Certificates
http://deployingradius.com/documents/configuration/certificates.html
http://deployingradius.com/documents/protocols/compatibility.htmlChild page description:
Overview - Description of the solution and documentation of custom scripts
Installation - Instructions on installing, and attachment containing scripts